 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| www..com Research Develop Innovate RDI, Inc. 400 Columbus Avenue Valhalla, NY 10595 : DC 50V 0.5A 1. RATING : 1P2T 2. FUNCTION 3. ELECTRICAL : NON-SHORTING ITEM PRACTICAL 4 TEMPERATURE RANGE STANDARD ATMOSPHERIC CONDITIONS TEST CONDITIONS -16C ~ + 60C PERFORMANCE 8. DURABILITY: ITEM 8.1 SOLDERABILITY TEST TEST CONDITIONS THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 230 5C FOR 3 0.5 SECONDS. PERFORMANCE THE AREA OF SOLDERING SHOULD BE OVER 75% WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TERMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. 5 NORMALLY,THE STANDARD RANGE OF ATMOSPHERIC CONDITION FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1) AMBIENT TEMPERATURE: 5 C TO 35 C (2) RELATIVE HUMIDITY: 45 % TO 85 % 6. ELECTRICAL CHARACTERISTICS 6.1 CONTACT RESISTANCE MEASURED AT SMALL CURRENT(100mA OR LESS) 1000Hz APPLY A VOLTAGE OF 500V DC SHALL BE APPLIED FOR 1 MIN. AFTER WHICH MEASUREMENT SHALL BE MADE. (1) BETWEEN TERMINALS. (2) BETWEEN INDIVIDUAL TERMINALS AND FRAME. AC 500V rms(50 - 60 HZ) FOR 1 MIN TRIP CURRENT: 0.5 mA (1)BETWEEN TERMINALS. (2) BETWEEN INDIVIDUAL TERMINALS AND FRAME. TEST CONDITIONS MEASUREMENT SHALL BE MADE AT THE NEAREST POINT OF THE COMPONENT OR AT THE POINT 3mm FROM THE TIP ON THE ACTUATOR(KNOB). 80 m MAX. 8.2 www..com INSULATION 6.2 RESISTANCE RESISTANCE TO SOLDERING HEAT TEST 100 M MIN. NO DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. PERFORMANCE 200gf 50gf 8.4 HEAT TEST SOLDER BATH METHOD: SOLDER TEMPERATURE 260 5C,IMMERSION TIME 3 0.5 SEC.IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6mm DIMENSIONS OF COMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL BEING ACCORDANCE THE SPECIFICATION. THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -20 3C FOR 96HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. THE SWITCH SHALL BE STORED AT A TEMPERATURE OF 85 2C FOR 48 HOURS, THEN IT SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. THE SWITCH SHALL BE STORED AT A TEMPERATURE OF 40 2C AND A HUMIDITY OF 90% TO 96 % FOR 96 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 6.3 DIELECTRIC STRENGTH 8.3 COLD TEST 7. MECHANICAL CHARACTERISTICS ITEM 7.1 OPERATING FORCE THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. A STATIC LOAD OF 300 gf SHALL BE APPLIED TO TERMINAL FOR 15 SEC. IN ANY DIRECTION. A STATIC LOAD OF 10N(1Kgf) SHALL BE DISPLACEMENT APPLIED TO THE TOP OF THE ACTUATOR (KNOB) AND THEN DISPLACEMENT SHALL 7.3 OF ACTUATOR BE MEASURED TO THE DIRECTION OF THE ARROW. (KNOB) 7.2 TERMINAL STRENGTH CHARACTERISTICS SHALL BE SATISFIED WITHOUT DAMAGE OR EXCESSIVE LOOSENESS OF TERMINALS. THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY WORK. AFTER TESTING: (1)CONTACT RESISTANCE: 100m MAX. (2)INSULATION RESISTANCE: 100M MIN. (3)WITHSTAND VOLTAGE: AC500V,1 MINUTE. (4)OPERATING FORCE : 30% INITIAL VALUE . (5)WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC . 8.5 HUMIDITY TEST 7.4 LIFE TEST ENDURANCE WITHOUT LOAD: A SWITCH SHALL BE SUBJECTED TO 10,000 CYCLES AT A SPEED OF 25 TO 30 CYCLES PER MINUTE WITHOUT LOAD. Research Develop Innovate RDI, Inc. 400 Columbus Avenue Valhalla, NY 10595 |
Price & Availability of SS-12E01-G21
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |